| WSC
2™
Weld Sequence Controller |
- The
WSC II™ Weld Sequence Control from Computer Weld
Technology, Inc. can bring total weld process control to
your system. Based on an embedded micro controller, this
unit provides two 0-10 VDC programmable outputs, one to
control the welding power source and the second, a CWT
Capstan Wire Feed Motor PWM Drive Control. Also provided
are 32 user selectable weld schedules and an optional 2-line
16-character Alpha Numeric LCD display for programming
the weld schedule data and to configure the control options.
The controller can be easily interfaced to your application
and can provide state-of-the-art control of your welding
process with a simplicity that is hard to find elsewhere.
-
With
32 programmable weld schedules, the WSC II™ provides
total flexibility in
your welding
environment. This controller can be used
to standardize the integration for all weld processes.
The WSC II™ can be supplied with or without a local
display and programming switches. The controller without
a local programming display and switches needs to be
programmed with either the WRP II™ Weld Remote
Pendant for on-line programming or the EZ-Edit Plus™ RS-232
Terminal Program for off-line programming. The controller
with a
local
programming display and switches can be programmed
directly from its front panel or use the EZ-Edit
Plus™ for off-line programming.
|
- Whether
new or old, CWT’s new WSC II™ bring total
weld process control to your system. The control provides
a standardized interface for all welding systems. It can
be used to control GMAW, SAW, PAW and GTAW welding systems.
The control will interface to most all solid state welding
power sources and wire feed drives. The optional PWM motor
drive can be provided that will control most low volt wire
drive motors. The control provides a simple user definable
Max/Min scaling to calibrate the
external power source output and wire drive speed range.
|
 |
|
WSC-1000
WELD SEQUENCE CONTROLLER - MECHANICAL SPECIFICATIONS
|
|
Dimensions
|
8.00" H X 10.50" W X 4.60" D (203mm X 267mm X 117mm)
|
|
Power Requirements
|
110/240 vac 50/60 Hz @ 0.2kw
|
|
Operating Temperature
|
-10° F to +140° F (-23° C to +60° C)
|
|
Relay Outputs
|
24 vdc @ 1 amp normally open contacts
|
Switch Inputs
|
5-24 vdc @ 1.0-8.0 ma
|
Analog Inputs
|
10-vdc precision reference output. 10-bit resolution (10 mv resolution). Maximum output current 10 ma. Output is short circuit protected. |
Encoder Input
|
Pulse accumulator input 5.0 vdc TTL level with 4.7K pull-up. Maximum input frequency 15 khz. |
Analog Inputs
|
0-10 vdc input, 8-bit resolution, 10 k ohm input impedance, non-isolated with over-voltage and polarity protection |
|
|
|
| FEATURES |
- Two isolated analog 0-10 vdc outputs and five solid-state isolated relay outputs
- Nine 24 vdc optically isolated inputs and three 0-10 vdc analog inputs
- Optional EZ-Edit Plus™ RS-232 Terminal Program for off-line programming
- On-line programming availiable with the WRP II Weld Remote Pendant or from the local display
- Weld event an I/O Status LED's
|
|
| BENEFITS |
- Provides simple interface to solid state power supplies and wire drive controls
- Allows remote user interface and weld schedule selection and provides remote control of the run time amp/volt or wire speed parameters
- Provides off-line weld schedule development and system configuration
- Provides a standardized user interface with easy to use menu driven display and fault status messages
- Indicates operationsl and I/O status
|
|
|
